Abstract
Employing post-combustion technology in the converter, using the sensible heat of the hot metal and the oxidation reaction heat as a heat source, is known to compensate for insufficient heat in the converter process. However, most studies on post-combustion have been conducted using subsonic nozzles, whereas actual converter processes use..... More

Abstract
MgO nanowires were grown by a thermal evaporation method at different N₂/O₂ gas ratios in order to investigate the effect of oxygen concentration on the growth and luminescence properties of the MgO nanowires. A thermal evaporation process was conducted at 1000^oC and under a pressure of 500Torr. No nanowires were..... More

Abstract
Wearable strain sensors with high and broad sensitivity, high stretchability and excellent mechanical endurance will be widely useful in smart wearable electronics. In this work, we developed a stretchable strain sensor fabricated with a simple stencil printing technique. The stretchable strain sensor was fabricated using a multi-walled carbon nanotubes (MWCNTs)-Ecoflex..... More

Abstract
In this study, we fabricated transparent heaters composed of an ultrathin Cu-layer heating element sandwiched between a ZnO underlayer and an Al₂O₃ overlayer. With the Cu layer thickness fixed at 8.5 nm, the thicknesses of the ZnO and Al₂O₃ layers were independently varied to reach the optimum antireflecting condition (maximum..... More

Abstract
The effects of Mg content and cooling rate on the T5 treatment of Al-Si-Mg alloys have been investigated using Avrami kinetics and transmission electron microscopy. The alloys were super-heated at 800 ^oC for 1 hr followed by degassing treatment at 720 ^oC for 15 min, and poured into a metallic..... More

Abstract
MgO nanowires with a branched structure were fabricated using a thermal evaporation method in air at atmospheric pressure. The branched MgO nanowire was made up of two parts: a primary central nanowire trunk and lots of secondary nanowire branches. The branched MgO nanowires had a 4-fold symmetrical structure. The secondary..... More

Abstract
Cu–Sb–Se ternary chalcogenide compounds composed of earth-abundant low-toxicity elements are attracting attention as economical and ecofriendly semiconductors. Among them, permingeatite (Cu₃SbSe₄) is a potential thermoelectric material with high Seebeck coefficient and low lattice thermal conductivity. However, it is necessary to improve its thermoelectric properties through doping, as it has low..... More

Abstract
Dihydrogen sulfide (H₂S) gas has a flammable nature and is one of the most toxic and dangerous gases. Even small concentrations can be fatal to humans. Herein, we investigated the H₂S gas-sensing features of commercial pristine cerium oxide (CeO₂ ) and gadolinium (Gd)-doped CeO₂ (GDC) nanoparticles. First, the sensing materials..... More

Abstract
The effect of Ni-based fillers on corrosion resistance of welded super austenitic stainless steel (SASS) was examined. The use of Ni-based fillers for gas tungsten arc welded SASS leads to the formation of fine Cr-Mo enriched phase in its weld unmixed zone, which makes it more susceptible to the localized..... More

Abstract
17-4 precipitation hardened stainless steel (17-4PH SS) has been reported to have excellent mechanical properties and excellent corrosion resistance, and is one of the materials used and studied with the powder bed fusion (PBF) method. Powder bed fusion (PBF) is a new manufacturing technology that has recently attracted attention in..... More

Abstract
We constructed a convolutional neural network to estimate average grain size from microstructure images. In the previous study from our research group, the network was trained using GB-type images in which the grain matrix and grain boundary were represented in white and black, respectively. The model well estimated the same..... More

Abstract
Bytizite (Cu₃SbSe₃ ) has attracted interest as a promising thermoelectric material because of its ultralow thermal conductivity; however, there are few experimental studies. This study investigated the optimal processing conditions for the synthesis of Cu₃SbSe₃ using mechanical alloying (MA) and hot pressing (HP). The MA powder exhibited an orthorhombic Cu₃SbSe₃..... More

Abstract
Famatinite (Cu₃SbS₄ ) is a promising p-type thermoelectric material because of its low lattice thermal conductivity and high Seebeck coefficient. In this study, famatinite powders, double-doped with Sn (a B^IV group element) and In (a B^III group element) to give Cu₃Sb_1-x-ySn_xIn_yS₄ (0.02 ≤ x ≤ 0.12 and 0.06 ≤..... More

Abstract
The amount and kind of additives in electrolytes play a very important role on the electroplating of Cu foil, which is used as a cathode materials for secondary batteries. As the use of Cu foil increased, various studies on the electroplated Cu foil are urgently needed. We studied surface characteristics..... More

Abstract
AA 2026 is an improved version of AA 2024, an alloy with added Zr to reduce Fe and Si content and inhibit recrystallization during hot working. Al 2026 alloy has high strength and high damage resistance, so it is widely used in aircraft parts. In this study, in order to..... More

Abstract
The effect of TiO₂ additive concentration and sintering temperatures on the densification of alumina (Al₂O₃ ) ceramics were investigated. Densified alumina specimens were prepared by uniaxial pressing at a pressure of 60 MPa followed by isothermal heating at either 1400, 1500, or 1600 o C for 2 h. The relative..... More

Abstract
TiB₂ is considered candidate materials for ultra-high temperature ceramics and cutting tools because of its a high thermal conductivity, a low coefficient of thermal expansion, a high hardness and high melting temperature. Despite these attractive properties, TiB2 applications are limited because it has a low fracture toughness below the brittle-ductile..... More

Abstract
Cast A356(Al-Si-Mg) alloys are widely used in automotive and general applications because of their mechanical properties and castability. Al-Si-Mg-(Cu) alloys typically lose their strength above 170 o C due to coarsening of precipitates, which limits their application to components. To maintain their strength at elevated temperature, Al-Si-Mg-(Cu) alloys are modified..... More

Abstract
Skinnerite (Cu₃SbS₃) has recently attracted attention as a promising thermoelectric material because of its low thermal conductivity. In this study, we performed the solid-state synthesis of Fe-doped skinnerite Cu₃Sb_1-yFe_yS₃ (y = 0.02−0.06) using mechanical alloying and hot pressing, and examined the samples’ thermoelectric properties relative to Fe doping content. All..... More

Abstract
Permingeatite (Cu₃SbSe₄) is a promising thermoelectric material with narrow bandgap energy and large carrier effective mass. However, doping is required to improve its electrical conductivity and thermoelectric properties. In this study, Cu₃Sb_1−y(Al/In)_ySe₄ doped with B^III-group elements (Al or In) at the Sb sites was synthesized using mechanical alloying followed by..... More

Abstract
To ensure the lifetime of marine constructions and the safety of workers and pedestrians, corrosion protective non-skid coating is an effective solution. However, the conventional polymer-based coating has some limitations. In this study, newly-suggested Al and Al-3%Ti coatings were deposited on high strength low alloyed steel substrate using twin wire..... More

Abstract
Technologies to reduce CO₂ emissions in the steel industry have been actively developed since the early 1990s in order to deal with global climate change. In particular, the utilization of various types of biomass including wood, bamboo, grass, food and agricultural by-product are being attempted as carbon neutral fuels in..... More

Abstract
Herein we report the optimized processing conditions of hot extrusion for fabricating an n-type Bi₂Te_2.7Se_0.3 thermoelectric compound, with high electronic transport properties as well as improved mechanical reliability. We fabricated a Bi₂Te_2.7Se_0.3 extrudate that was 3.8 mm in diameter and 700 mm in length by controlling the processing parameters of..... More

Abstract
YbCd₂Sb₂ is a promising Zintl compound for waste heat recovery applications due to its low thermal conductivity, originating from its complex crystal structure. Many strategies such as alloying or doping have been suggested to further reduce the thermal conductivity of YbCd₂Sb₂ to improve its thermoelectric performance. However, the..... More

Abstract
Green hydrogen has attracted significant attention as one of the future energy sources because no greenhouse gases are emitted during production and its energy density is much higher than fossil fuels. Precious metals such as platinum (Pt) and iridium (Ir)-based catalysts are commonly used for water splitting catalysts. However, because..... More

Abstract
The effects of fabrication method on the microstructure and sinterability of W-1 wt% Y₂O₃ were analyzed. W composite powders dispersed with Y₂O₃ particles were synthesized by the ultrasonic spray pyrolysis process or the ultrasonic spray pyrolysis/polymer solution process. A dense composite was fabricated by a combination of spark plasma sintering..... More

Abstract
The effects of the electrogalvanizing conditions (a combination of plating current and time) on hydrogen infusion, embrittlement, and corrosion-induced hydrogen embrittlement (HE) behaviors of ultra-high strength steel were examined. A range of experimental and analytical methods, including electrochemical impedance spectroscopy, hydrogen permeation, polarization, and slow strain rate test, were employed...... More

Abstract
There is substantial concern about the phase change to artificial ferrite or martensite in commercial austenitic stainless steels during intense focused-ion-beam milling. In this work, severe Ga ion milling to prepare microscale samples was found to produce thin transformed layers on the surface of austenitic stainless steel. The surface BCC..... More

Abstract
The efficiency of gas turbines depends on the gas turbine working temperature. Single crystal blades are being applied more often than equiaxed blades in gas turbine engines, to increase the turbine inlet temperature, resulting in enhanced turbine engine efficiency. Single crystal blades endure creep conditions at high temperature better than..... More

Abstract
In the present study, we analyzed the thermal and mechanical properties of Cu-graphite composites (CGCs) with spatially anisotropic graphite layers. These composites were fabricated using a combination of electroless plating and spark plasma sintering (SPS) processes. Thermal conductivities and thermal expansion coefficients of the composites were measured using differential thermal..... More